(WTFT-2357) Caster Cut-off Torch

OUTSTANDING FEATURES

  • Small Cutting Kerf
  • Up to 50% reduction in width
  • Longer Stand-Off
  • Longer life, less torch damage and wear
  • Small Slag Dross
  • Less metal loss and slag removal
  • Good Cut Quality
  • Sharper edges, straighter cut
  • Faster Cutting Speed
  • 14-17IPM, double conventional torches
  • Increased Nozzle Life
  • Less change over
  • Quick Nozzle Change
  • The tip is the nut
  • Low Consumption
  • Uses 20% less oxygen
  • Wide Working Ranges
  • Thickness from 2-30" (50-750mm)
  • Reduce Flashback Hazards
  • Increased safety and less damage
  • Flying Start vs. Preheat Dwell
  • Quicker overall cut time

The WTFT is the state-of-the-art cutting torch for steel mill cut-off and secondary cutting operations. The torch body is stainless steel for longer life. The solid bras head and large volume water cooled body allows for cooler operation and gvies increased torch life in limited water loss environment. The supply tubes support ring lessens fitting or tube damage due to torch change over or accidental impacts. The factory remanufacturing program is available for these types of torches.

Weld Tip can supply the WTFT torch in any required length and can design and supply specialty torch configurations upon request.

 

WTFN NOZZLE (REPLACEMENT FOR Gega® SDS SERIES)

The WTFN is a heavy duty cutting nozzle for all machine or specialty cut-off applications. It is designed for a wide range of thicknesses, up to 30" and operates with most available fuel and oxygen.

 

WTFNL NOZZLE (IMPROVED WELD TIP DESIGN TO REPLACE Gega® SDS SERIES)

The WTFNL is the latest nozzle designed to perform at the higher end speed range, while at the low end pressure range yielding a narrower kerf, thereby increasing efficiency.

The nozzle pre-mixing/post-mixing design and use of a well-defined diverged cutting oxygen stinger allows for faster starts, narrower kerfs, lower consumption and a longer stand-off. The factory remanufacturing program is available for these nozzles.

 

Nozzle Information

Nozzle Style Gega® Equiv.  

Ringfire

(RSD-1)

 WTCN-1

(SDK-1)

 WTFN-1 (SDS-26F) WTDNL-1 WTFN-2 (SDS-26F) WTFNL-2 WTFM-3 (SDS-33F) WTFNL-3 WTFM-4 (SDS-36F) WTFNL-4
THICKNESS

CUTTING OXYGEN PRESSURE

P/H OXYGEN PRESSURE

PROPANE PRESSURE

NATURAL GAS PRESSURE

COKE OVEN GAS PRESSURE

CUTTING SPEED @ 20C-170C

CUTTING SPEED @ 750F-1400F

KERF WIDTH @ 20C-70F

KERF WIDTH 750C-1400F

NOZZLE DISTANCE

BEARD WIDTH @ 750F-1400F

BEARD THICKNESS @ 750f-1400f

NOISE LEVEL dBA
 
(IN)
(MM)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
IN/MM
MM/MIN
IN/MM
MM/MIN
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(MM)
 
2-12
50-300
100-150
6.9-10.4
35-40
2.4-3.1
4-6
0.3-0.4
8-10
0.6-0.7
30-35
2.1-2.4
10-12
250-300
16-18
400-450
0.40-0.47
10.0-12.0
0.40-0.55
12.0-14.0
2-5
60-120
0.9-1.1
22-27
0.5-0.6
12-15
108-115
 
2-12
50-300
130-200
9.0-3.9
30-35
2.1-2.4
4-10
0.3-0.7
15-25
1.0-1.7
25-30
1.7-2.1
10-12
250-300
14-17
350-420
0.40-0.50
10.0-14.0
0.40-0.63
12.0-16.0
2-5
60-120
0.6-0.7
14-18
0.6-0.7
15-18
105-112
 
2-20
50-250
140-250
9.7-17.4
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
6-11
150-280
11-17
280-440
0.21-0.28
5.5-7.0
0.20-0.26
5.0-6.5
4-6
100-140
0.6-0.7
14-18
0.2-0.3
6-8
102-109
 
2-30
50-750
115-200
8.0-13.9
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
7-9
180-240
12-16
300-400
0.21-0.30
5.5-7.5
0.24-0.31
6.0-8.0
4-6
100-140
0.6-0.7
15-19
0.3-0.4
7-9
100-106
 
2-30
50-750
115-160
8.0-11.1
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
7-9
180-240
12-16
300-400
0.28-0.35
7.0-9.0
0.28-0.35
7.0-9.0
4-6
100-140
0.7-0.9
18-22
0.3-0.4
7-11
100-106
 
2-30
50-750
130-175
9.0-12.0
30-45
2.0-3.0
7-12
0.4-0.8
15-30
1.0-2.1
25-35
1.7-2.4
7-11
180-280
12-20
300-520
31-40
8.0-10.0
0.35-0.43
9.0-11.0
4-6
100-140
0.7-0.9
18-22
0.35-0.5
9-13
100-106

Cutting speeds, kerf thickness and widths are based on 8 inch (200 mm) thickness - mild carbon steel material. Pressures are recommended optimum conditions, it may be necessary to make adjustments based on material. The WTFNL's are designed to perform at the higher end speed range, while at the low end pressure range, yielding a narrower kerf, thereby increase efficiency.

STEEL MILL CUTTING EQUIPMENT "Gega®" STYLE CROSS REFERENCE

 Gega® Number WELD TIP Number Description
Torches  SB-500F
         N/A
         N/A
 
WT-GFT-500F
WTFT-XX*
WTFT-A-XX*
 
Water cooled Gega® design
Water cooled design
Air cooled design
Nozzles  SDS-26F
         SDS-33F
         SDS-33FP
         SDS-36F
         SDH-40F
         N/A
 
WTFN-1
WTMN-2
WTMNP-2
WTMN-3
WTMN-4
WTMNL-1-4
 
Flat Seat Nozzle
Flat Seat Nozzle
Flat Seat Nozzle - Powder Cutting
Flat Seat Nozzle
Flat Seat Nozzle
Extended Length Design
Flat Seat Nozzle

 

The above equipment is available for delivery immediately and is F.O.B. Oakville, ON. All taxes extra, all prices listed are in Canadian funds.

Parts for the above equipment can be supplied,and we have the facilities to service and repair the listed equipment.