Weld Tip Bull Barrel Heavy Duty Cutting Tips
Bull Barrel Tips for Smith® Torches
RECOMMENDED TORCH CAPACITY:
The following SMITH® torches will accept the Bull Barrel Smith® cutting tips, but are limited in capacity according to the following chart:
Maximum Tips Size Used Torch or Torch Series 5 6 9 SC209, SC205, SC200, SC505, SC509, SC409 SC229, SC220, SC225, SC175, SC179, SC275 SC279, SC265, SC369, SC225S, SC229S, SC770, SC771, SC850, SC860 SC720, SC725, SC729, SC730, SC725, SC729 SC780A, SC781A, SC782A
Natural Gas/PropanePropylene
MAPP
STYLE SIZE STYLE SIZESTYLE SIZE SN SNF SNB SNX SNFX SNH SNFH SNXH SNFXH SNGB-2 SNGS-2 SNGS-4 SNGS-5 SNR SNRX SN STUB SNRB SN-8 SN-10 SN-14 S-SCRAPPER 5/0-9 5/0-9 00-6 000-6 000-6 5/0-6 5/0-6 000-6 000-6 1-6 1-6 20,25 4,5,6 0-3 1-5 1-6 1-6 1-6 2-6,8,10,12 SP SPX SPH SPXH SPGB-2 SPGS-2 SPGS-4 SPGS-5 SPR SPRX SP STUB SPRB SP-8 SP-10 SP-14 5/0-9 000-6 5/0-6 000-6 1-6 1-6 20,25 4,5,6 0-3 1-5 1-6 1-6 1-6 SM SMX SMH SMXH SMGB-2 SMGS-2 SMGS-4 SMGS-5 SMR SMRX SM STUB SMRB SM-8 SM-10 SM-14 5/0-9 000-6 5/0-6 000-6 1-6 1-6 20,25 4,5,6 0-3 1-5 1-6 1-6 1-6
Bull Barrel Tips for Meco® Torches
RECOMMENDED TORCH CAPACITY:
The following MECO® torches will accept the Bull Barrel Meco® cutting tips, but are limited in capacity according to the following chart:
Natural Gas/Propane |
Propylene |
MAPP | |||
STYLE |
SIZE |
STYLE |
SIZE |
STYLE | SIZE |
MN MNF MNH MNFH MNGS-2 MNGS-5 MNR |
5/0-6 5/0-6 5/0-6 5/0-6 1-6 4,5,6 |
MP MPH MPGS-2 MPGS-5 MPR |
5/0-6 5/0-6 1-6 4,5,6 |
MM MMH MMGS-2 MMGS-5 MMR |
5/0-6 5/0-6 1/6 4,5,6 |
Standard Pressure Tips
Bull Barrel Standard Pressure tips have converged straight bore oxygen jets for general purpose cutting with hand and machine torches. All tips feature shells machined from solid copper bar stock for increased tip life, rather than the thin upset tubing used by several leading OEM's. Bull Barrel tips offer four diameters of splined internals to assure optimum amount of preheat for thickness of material being cut. Most OEM's offer only two or three diameters of internals to cover all sizes.
Cutting oxygen pressures for Bull Barrel general purpose tips range from 15-60 psi depending on tip size.
HIGH PRESSURE TIPS
Bull Barrel High Pressure tips have converged-diverged bores that yield extremely high velocity cutting oxygen jets. These high velocity cutting oxygen jets increase cutting speeds up to 20% and decrease kerf widths. All high pressure tips are hand diverged and tested at cutting oxygen pressures between 70-100 psi depending on tip size. High pressure tips are ideal for machines capable of running smooth at the increased speeds.
Bull Barrel
The extra heavy shell of the Bull Barrel cutting tip is specially designed to last longer under heavy use. The Bull Barrel is widely used in scrap yards and rail yards and is ideal for any job where cutting tips receive abusive treatment.
The Bull Barrel shell is machined from solid copper bar stock making it considerably heavier than the leading OEM shell, which is swagged from copper tubing and tends to deteriorate faster especially under tough conditions. Bull Barrels are available in all fuel gases for all major torch brands. Other brands of torches may realize the benefits of the Bull Barrel tips with a universal tip.
Extra Preheat Tips The Bull Barrel Extra Preheat tip features a larger diameter internal than the same size in a general purpose tip. The larger preheat diameter decreases preheat time and increases cutting speeds up to 25% over most OEM's. The extra preheat is ideal for cutting plate from 3/8" to 3" thick, for ripping and as a lead tip in single or double bevelling. The Bull Barrel Extra Preheat tip is not recommended for material thickness less than 3/8" or over 4", nor for piercing or cutting dirty material that would tend to prematurely clog the larger exposed area of preheat. |
|
SUPER COARSE SPLINE
THE SUPER COARSE SPLINE tip is ideal for cutting rusty, painted and dirty plate by hand. The internal has 12 large V-shaped splines to accommodate a tremendous amount of fuel. The very coarse spline congifuration does not easily clog from slag, paint and rust. Clogged splines may be cleaned quickly and easily with a pocket knife. The SUPER COARSE SPLINE is designed to eliminate considerable downtime and replacement cost. |
|
The above equipment is available for delivery immediately and is F.O.B. Oakville, ON. All taxes extra, all prices listed are in Canadian funds.
Parts for the above equipment can be supplied,and we have the facilities to service and repair the listed equipment.