Nozzle Information

 

Nozzle Style Gega Equiv.  

Ringfire

(RSD-1)

 WTCN-1

(SDK-1)

 WTFN-1 (SDS-26F) WTDNL-1 WTFN-2 (SDS-26F) WTFNL-2 WTFM-3 (SDS-33F) WTFNL-3 WTFM-4 (SDS-36F) WTFNL-4
THICKNESS

CUTTING OXYGEN PRESSURE

P/H OXYGEN PRESSURE

PROPANE PRESSURE

NATURAL GAS PRESSURE

COKE OVEN GAS PRESSURE

CUTTING SPEED @ 20C-170C

CUTTING SPEED @ 750F-1400F

KERF WIDTH @ 20C-70F

KERF WIDTH 750C-1400F

NOZZLE DISTANCE

BEARD WIDTH @ 750F-1400F

BEARD THICKNESS @ 750f-1400f

NOISE LEVEL dBA
 
(IN)
(MM)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
(PSI)
(BAR)
IN/MM
MM/MIN
IN/MM
MM/MIN
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(IN)
(MM)
(MM)
 
2-12
50-300
100-150
6.9-10.4
35-40
2.4-3.1
4-6
0.3-0.4
8-10
0.6-0.7
30-35
2.1-2.4
10-12
250-300
16-18
400-450
0.40-0.47
10.0-12.0
0.40-0.55
12.0-14.0
2-5
60-120
0.9-1.1
22-27
0.5-0.6
12-15
108-115
 
2-12
50-300
130-200
9.0-3.9
30-35
2.1-2.4
4-10
0.3-0.7
15-25
1.0-1.7
25-30
1.7-2.1
10-12
250-300
14-17
350-420
0.40-0.50
10.0-14.0
0.40-0.63
12.0-16.0
2-5
60-120
0.6-0.7
14-18
0.6-0.7
15-18
105-112
 
2-20
50-250
140-250
9.7-17.4
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
6-11
150-280
11-17
280-440
0.21-0.28
5.5-7.0
0.20-0.26
5.0-6.5
4-6
100-140
0.6-0.7
14-18
0.2-0.3
6-8
102-109
 
2-30
50-750
115-200
8.0-13.9
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
7-9
180-240
12-16
300-400
0.21-0.30
5.5-7.5
0.24-0.31
6.0-8.0
4-6
100-140
0.6-0.7
15-19
0.3-0.4
7-9
100-106
 
2-30
50-750
115-160
8.0-11.1
30-45
2.0-3.1
7-10
0.5-0.7
15-30
1.0-2.1
25-35
1.7-2.4
7-9
180-240
12-16
300-400
0.28-0.35
7.0-9.0
0.28-0.35
7.0-9.0
4-6
100-140
0.7-0.9
18-22
0.3-0.4
7-11
100-106
 
2-30
50-750
130-175
9.0-12.0
30-45
2.0-3.0
7-12
0.4-0.8
15-30
1.0-2.1
25-35
1.7-2.4
7-11
180-280
12-20
300-520
31-40
8.0-10.0
0.35-0.43
9.0-11.0
4-6
100-140
0.7-0.9
18-22
0.35-0.5
9-13
100-106

Cutting speeds, kerf thickness and widths are based on 8 inch (200 mm) thickness - mild carbon steel material. Pressures are recommended optimum conditions, it may be necessary to make adjustments based on material. The WTFNL's are designed to perform at the higher end speed range, while at the low end pressure range, yielding a narrower kerf, thereby increase efficiency.

STEEL MILL CUTTING EQUIPMENT "GEGA" STYLE CROSS REFERENCE

 Gega Number WELD TIP Number Description
Torches  SB-500F
         N/A
         N/A
 
WT-GFT-500F
WTFT-XX*
WTFT-A-XX*
 
Water cooled Gega design
Water cooled design
Air cooled design
Nozzles  SDS-26F
         SDS-33F
         SDS-33FP
         SDS-36F
         SDH-40F
         N/A
 
WTFN-1
WTMN-2
WTMNP-2
WTMN-3
WTMN-4
WTMNL-1-4
 
Flat Seat Nozzle
Flat Seat Nozzle
Flat Seat Nozzle - Powder Cutting
Flat Seat Nozzle
Flat Seat Nozzle
Extended Length Design
Flat Seat Nozzle